U-Value Tool Frame U-Value

Description

With the U-Value tool Frame U-Value you can calculate and display Frame Uf-Values according to EN ISO 10077-2.

How do I activate it?

The U-Value tool can be activated with the command U-Value in the menu Results or by clicking on the icon in the Toolbox flyout. Then select Frame Uf-Value as kind in the tool properties (cf. figure 3).

How do I use it?

Click with the tool on the result object for which the Uf-value should be calculated. If flixo professional recognizes the construction as a frame according to EN ISO 10077-2 then a dialog window opens.

For the calculation of the window frame U-value according to the European standard EN ISO 10077-2, the glass unit has to be replaced by a panel (cf. figure 1) with the following characteristics:

•	The thickness of the panel should correspond to the thickness of the glass unit.

•	The thickness of the air cavity between the panel and the frame (cf. b1) should at least be 5mm thick.

•	The glass unit rebate (cf. b2) of the panel should be 15 mm at the most.

•	The visible part of the panel (cf. bp) should at least be 190 mm.

•	According to EN ISO 10077-1, the measurements b2 and bp should correspond to the larger of the two projected widths of the frame section, without taking into account the stripping between the frame and glass unit or panel (cf. figure 2).

•	The thermal conductivity of the panel should be 0.035 W/(mK).

Figure 1: Preconditions for a Uf-value calculation

You have to define the frame materials which determine the frame measurements in the opening dialog window.

You can adjust afterwards the calculation kind for the frame width with the selected frame materials (Max of projections, Cold side projection, Warm side projection) as well the frame materials themselves in the Properties flyout (cf. figure 2).

Figure 2: Properties flyout for an Uf-value object

The calculation of a frame U-value is explained in detail in tutorial 4.

In special cases, if the frame width can't be exactly defined with the materials (e.g. "Z-Profiles"), you can also adapt the dimension manually by moving the position of the start points of the dimension objects using the Select, Move, Scale tool. You can also change the text positions of the help objects, of the U-values of the base construction and the dimension lines with the same tool.

Defining Styles

The presentation of an Uf-value object can be selected in the Style list in the tool properties (cf. figure 3). The list shows all styles for Uf-value objects that have previously been determined in the Styles flyout.

A new Uf-value object is always created with the styles currently marked in the Style drop down list. You can either change the selection of the styles in the Styles flyout or select the according style in the Style drop down list of the tool properties.

The styles can also be adjusted afterwards by using the Assign Properties tool or by using the Drag&Drop function (cf. tutorial 1).

Figure 3: Tool Properties

Physical Explanations

The frame U-value is calculated according to EN ISO 10077-2 as follows:

Figure 4: Calculation of Uf-values

with:

Φ: Total heat flux in to or out of the model [W/m]

ΔT: Temperature difference [K]

Up: U-value of the panel [W/m2K]

bp: Width of the panel [m]

bf: Width of the frame [m]

If the calculated construction is a mullion or a transom, than 2 panels are used instead of the glazings, the formula is as follows:

Limitations

This option is only available for constructions, which are recognized as window frame U-value according to EN ISO 1007-2:

•	The thermal conductivity of the panel is 0.035 W/(mK).

•	The visible part of the panel is at least 190 mm.

•	There are exactly 2 air temperatures on the boundary conditions.

•	There are exactly 2 adiabatic boundary conditions ("Symmetry/Model Section" ) each one on both model sections.

•	Either it's a horizontal or a vertical window

Url: http://www.infomind.ch/bph/de/flixo/manual/version6/index.html?tools_uvalue_uf.htm